arobase1024

Non, rien à voir avec la carte mere .... il démarre

Bonjour, Bad Magic Number L'appareil termine son boot par ce message. C'est juste à la fin de mon dernier poste. le NAS est en "lumière bleue de la mort", j'essaie de le recuperer par tftpboot mais je n'y arrive pas. bootcmd=bootm F8080000 F8280000 Ceci est la sequence de boot automatique du NAS, qui si j'ai bien compris, F8080000 correspond à l'adresse de chargement dans la mémoire du fichier zimage.img et F8280000 à l'adresse de chargement dans la mémoire du fichiers rd.bin. Comment convertir ces valeurs f8080000 et f8280000 en hexa sous la forme "0x000000" pour mettre ces deux fichiers en ram correctement à leurs place ? Merci.

bonjour, Après pas mal de recherche sur la toile, comme le NAS n'est pas jeune, il faut fouiner, cela doit provenir du boot et non des disques dur. j'ai bien acces au NAS par le port serie, je configure le server pour pouvoir executer tftpboot pour les fichiers de démarrage que je veux lui mettre, mais la ou je fait une erreur doit être l'adresse hexa ou il faut mettre les fichiers. dans mon log suivant, le boot se fait sur l'adresse, f8080000 : a quelle adresse hexa cela correspond-il et quel fichier doit ce trouver à cette adresse ? __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** MARVELL BOARD: Synology Disk Station LE U-Boot 1.1.4 (Apr 15 2011 - 15:51:31) Marvell version: 3.5.9 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B3D4 Soc: 88F6282 A0CPU running @ 1600Mhz L2 running @ 533Mhz SysClock = 533Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7 DRAM CS[0] base 0x00000000 size 512MB DRAM Total size 512MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done Using default environment [4096kB@f8000000] Flash: 4 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 PEX 1: interface detected no Link. Synology Model: DS411 Fan Status: Good Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 ## Booting image at f8080000 ... Bad Magic Number Marvell>>

bonsoir, oui elle est neuve aussi.

ok, j'ai réessayé le disque que l'on m'a fourni avec le nas formaté sous macos et toujours pareil.

oui je me doutais bien. Mais le résultat est toujours le même ... [ 38.170000] No filesystem could mount root, tried: ext3 ext2 ext4 [ 38.180000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(9,0) il y a bien quelque chose que je dois mal faire ! le nas ne demarre toujours pas tous seul, il faut que je remette le fichier zimage.img et que je lance bootm pour le démarrer.a chaque fois

Bonsoir, non je n'ai pas mis de disques neuf et même avec un vieux disque formaté, il ne démarre toujours pas et l'assistant ne reconnais toujours pas le nas vu qu'il ne démarre pas correctement. Du coup j'ai inséré un seul vieux disque formaté en ext2 mais pareil ... Je peux ressayer de le formater en Ext pour voir .....

Bonsoir, J'ai voulus redémarrer un ds411 que je venais d'acheter la semaine dernière et patatra, a la fin de l'installation du dernier DSM compatible pour lui, l'assistant Synology me dit que l'installation c'est mal passée et qu'il fallait contacter le SAV. Résultat, voyant bleu power clignotant ! Je me suis donc connecté avec le port série, j'ai réussi à démarrer le nas avec l'image correspondant à mon appareil mais un message apparait lors du redemarrage et il ne va pas plus loin. Quelqu'un aurait-il une idée, mes compétences s'arretent là avec unix, je vous donne le log Merci de votre aide. ▒ __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** MARVELL BOARD: Synology Disk Station LE U-Boot 1.1.4 (Apr 15 2011 - 15:51:31) Marvell version: 3.5.9 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 0068B3D4 Soc: 88F6282 A0CPU running @ 1600Mhz L2 running @ 533Mhz SysClock = 533Mhz , TClock = 200Mhz DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7 DRAM CS[0] base 0x00000000 size 512MB DRAM Total size 512MB 16bit width Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done Using default environment [4096kB@f8000000] Flash: 4 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: PCI Express Root Complex Interface PEX interface detected Link X1 PEX 1: interface detected no Link. Synology Model: DS411 Fan Status: Good Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 0 ## Booting image at f8080000 ... Bad Magic Number Marvell>> setenv serverip 192.168.1.66 Marvell>> tftpboot *** Warning: no boot file name; using 'C0A8019A.img' Using egiga0 device TFTP from server 192.168.1.66; our IP address is 192.168.1.154 Filename 'C0A8019A.img'. Load address: 0x800000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ############################################ done Bytes transferred = 1553696 (17b520 hex) Marvell>> bootm ## Booting image at 00800000 ... Image Name: Linux-2.6.32.12 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1553632 Bytes = 1.5 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. [ 0.000000] Linux version 2.6.32.12 (root@build4) (gcc version 4.6.4 (Marvell GCC release 20150204-c4af733b 64K MAXPAGESIZE ALIGN CVE-2015-0235) ) #25556 Thu Mar 4 17:56:48 CST 2021 [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397 7 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Synology 6282 board [ 0.000000] Using UBoot passing parameters structure [ 0.000000] Sys Clk = 200000000, Tclk = 166666667 [ 0.000000] Synology Board ID: 26 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pa ges: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 ip=off initrd=0x0080004 0,4M root=/dev/md0 rw syno_hw_version=DS411v10 ihd_num=4 netif_num=1 [ 0.000000] Synology Hardware Version: DS411v10-j [ 0.000000] Internal HD num: 4 [ 0.000000] Internal netif num: 1 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 512MB = 512MB total [ 0.000000] Memory: 506880KB available (3656K code, 519K data, 124K init, 0K highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:128 [ 0.000000] Console: colour dummy device 80x30 [ 0.000000] Calibrating delay loop... 1589.24 BogoMIPS (lpj=7946240) [ 0.240000] Mount-cache hash table entries: 512 [ 0.240000] CPU: Testing write buffer coherency: ok [ 0.240000] devtmpfs: initialized [ 0.240000] xor: measuring software checksum speed [ 0.290000] arm4regs : 1448.800 MB/sec [ 0.340000] 8regs : 869.200 MB/sec [ 0.390000] 32regs : 1122.000 MB/sec [ 0.390000] xor: using function: arm4regs (1448.800 MB/sec) [ 0.390000] NET: Registered protocol family 16 [ 0.390000] Feroceon L2: Enabling L2 [ 0.390000] Feroceon L2: Cache support initialised, in WT override mode. [ 0.410000] [ 0.410000] CPU Interface [ 0.410000] ------------- [ 0.410000] SDRAM_CS0 ....base 00000000, size 512MB [ 0.410000] SDRAM_CS1 ....disable [ 0.410000] SDRAM_CS2 ....disable [ 0.410000] SDRAM_CS3 ....disable [ 0.410000] PEX0_MEM ....base e0000000, size 128MB [ 0.410000] PEX0_IO ....base f2000000, size 1MB [ 0.410000] PEX1_MEM ....base e8000000, size 128MB [ 0.410000] PEX1_IO ....base f2100000, size 1MB [ 0.410000] INTER_REGS ....base f1000000, size 1MB [ 0.410000] NFLASH_CS ....base fa000000, size 2MB [ 0.410000] SPI_CS ....base f4000000, size 16MB [ 0.410000] BOOT_ROM_CS ....no such [ 0.410000] DEV_BOOTCS ....no such [ 0.410000] CRYPT_ENG ....base f0000000, size 2MB [ 0.410000] Detected Tclk 200000000 and SysClk 533333333 [ 0.410000] Apply DS 411 GPIO [ 0.410000] Synology 6282 DS411 GPIO Init [ 0.410000] PCIe link is enable, apply PCIe workaround [ 0.910000] PEX0 interface detected Link X4 [ 1.410000] PEX1 interface detected no Link. [ 1.410000] PCI: bus0: Fast back to back transfers disabled [ 1.410000] PCI: bus1: Fast back to back transfers enabled [ 1.420000] bio: create slab <bio-0> at 0 [ 1.420000] vgaarb: loaded [ 1.420000] SCSI subsystem initialized [ 1.590000] raid6: int32x1 126 MB/s [ 1.760000] raid6: int32x2 185 MB/s [ 1.930000] raid6: int32x4 180 MB/s [ 2.100000] raid6: int32x8 193 MB/s [ 2.100000] raid6: using algorithm int32x8 (193 MB/s) [ 2.100000] Switching to clocksource kw_clocksource [ 2.100000] NET: Registered protocol family 2 [ 2.100000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 2.100000] TCP established hash table entries: 16384 (order: 5, 131072 bytes ) [ 2.100000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 2.100000] TCP: Hash tables configured (established 16384 bind 16384) [ 2.100000] TCP reno registered [ 2.100000] NET: Registered protocol family 1 [ 2.100000] RPC: Registered udp transport module. [ 2.100000] RPC: Registered tcp transport module. [ 2.100000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.100000] Trying to unpack rootfs image as initramfs... [ 2.100000] Freeing initrd memory: 4096K [ 2.100000] XOR registered 4 channels [ 2.100000] XOR 2nd invalidate WA enabled [ 2.100000] VFS: Disk quotas dquot_6.5.2 [ 2.100000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.100000] msgmni has been set to 998 [ 2.100000] alg: No test for md5 (md5-generic) [ 2.100000] alg: No test for des (des-generic) [ 2.100000] alg: No test for des3_ede (des3_ede-generic) [ 2.100000] alg: No test for stdrng (krng) [ 2.100000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2 54) [ 2.100000] io scheduler noop registered [ 2.100000] io scheduler anticipatory registered (default) [ 2.110000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.110000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A [ 2.120000] console [ttyS0] enabled [ 2.120000] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A [ 2.130000] brd: module loaded [ 2.140000] sata_mv 0000:00:01.0: version 1.28 [ 2.140000] PCI: enabling device 0000:00:01.0 (0140 -> 0143) [ 2.150000] sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx [ 2.160000] scsi0 : sata_mv [ 2.160000] scsi1 : sata_mv [ 2.160000] scsi2 : sata_mv [ 2.170000] scsi3 : sata_mv [ 2.170000] ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 irq 9 [ 2.180000] ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 irq 9 [ 2.180000] ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 irq 9 [ 2.190000] ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 irq 9 [ 7.690000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 7.710000] ata1.00: ATA-8: ST250DM000-1BD141, HP73, max UDMA/100 [ 7.710000] ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 7.760000] ata1.00: configured for UDMA/100 [ 7.780000] scsi 0:0:0:0: Direct-Access ATA ST250DM000-1BD141 HP73 PQ: 0 ANSI: 5 [ 7.780000] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB) [ 7.790000] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 7.800000] sd 0:0:0:0: [sda] Write Protect is off [ 7.800000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, does n't support DPO or FUA [ 7.810000] sda: sda1 sda2 sda3 sda4 [ 7.890000] sd 0:0:0:0: [sda] Attached SCSI disk [ 10.890000] Delay 5 seconds to wait for disk 2 ready. [ 20.180000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 20.280000] ata2.00: ATA-7: ST3250310AS, 3.AAB, max UDMA/133 [ 20.280000] ata2.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 20.330000] ata2.00: configured for UDMA/133 [ 20.350000] scsi 1:0:0:0: Direct-Access ATA ST3250310AS 3.AA PQ: 0 ANSI: 5 [ 20.350000] sd 1:0:0:0: [sdb] 488397168 512-byte logical blocks: (250 GB/232 GiB) [ 20.360000] sd 1:0:0:0: [sdb] Write Protect is off [ 20.370000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, does n't support DPO or FUA [ 20.380000] sdb: sdb1 [ 20.390000] sd 1:0:0:0: [sdb] Attached SCSI disk [ 23.390000] Delay 5 seconds to wait for disk 3 ready. [ 28.740000] ata3: SATA link down (SStatus 0 SControl 300) [ 31.740000] Delay 5 seconds to wait for disk 4 ready. [ 37.080000] ata4: SATA link down (SStatus 0 SControl 300) [ 37.080000] sata_mv sata_mv.0: version 1.28 [ 37.080000] sata_mv sata_mv.0: slots 32 ports 2 [ 37.090000] scsi4 : sata_mv [ 37.090000] scsi5 : sata_mv [ 37.100000] ata5: SATA max UDMA/133 irq 21 [ 37.100000] ata6: SATA max UDMA/133 irq 21 [ 37.450000] ata5: SATA link down (SStatus 0 SControl F300) [ 37.800000] ata6: SATA link down (SStatus 0 SControl F300) [ 37.800000] physmap platform flash device: 00400000 at f8000000 [ 37.810000] SPI Serial flash detected @ 0xf8000000, 4096KB (64sec x 64KB) [ 37.820000] Searching for RedBoot partition table in SYNOMTD-0 at offset 0x3f 0000 [ 37.830000] 6 RedBoot partitions found on MTD device SYNOMTD-0 [ 37.830000] SYNOMTD flash bank 0: Using RedBoot partition definition [ 37.840000] Creating 6 MTD partitions on "SYNOMTD-0": [ 37.850000] 0x000000000000-0x000000080000 : "RedBoot" [ 37.850000] 0x000000080000-0x000000280000 : "zImage" [ 37.860000] 0x000000280000-0x0000003c0000 : "rd.gz" [ 37.860000] 0x0000003c0000-0x0000003d0000 : "vendor" [ 37.870000] vender Mac1 checksum error ucSum:0x00 Buf:0x00 Sum:0. [ 37.870000] vender Mac2 checksum error ucSum:0x00 Buf:0x00 Sum:0. [ 37.880000] vender Mac3 checksum error ucSum:0x00 Buf:0x00 Sum:0. [ 37.890000] serial number='BAJ1N01736' [ 37.890000] 0x0000003d0000-0x0000003f0000 : "RedBoot Config" [ 37.900000] 0x0000003f0000-0x000000400000 : "FIS directory" [ 37.900000] SPI Serial flash detected @ 0xf4000000, 4096KB (64sec x 64KB) [ 37.910000] cmdlinepart partition parsing not available [ 37.920000] Loading Marvell Ethernet Driver: [ 37.920000] o Cached descriptors in DRAM [ 37.930000] o DRAM SW cache-coherency [ 37.930000] o 2 Giga ports supported [ 37.930000] o Single RX Queue support - ETH_DEF_RXQ=0 [ 37.940000] o Single TX Queue support - ETH_DEF_TXQ=0 [ 37.940000] o TCP segmentation offload (TSO) supported [ 37.950000] o Receive checksum offload supported [ 37.950000] o Transmit checksum offload supported [ 37.960000] o SKB Recycle supported - (Enabled) [ 37.960000] o Rx descripors: q0=128 [ 37.970000] o Tx descripors: q0=532 [ 37.970000] o Loading network interface(s): [ 37.980000] o register under mv88fx_eth platform [ 37.980000] o eth0, ifindex = 2, GbE port = 0 [ 37.990000] o eth0, phy chipid = 1410e90, Support WOL = 32 [ 37.990000] [ 37.990000] md: linear personality registered for level -1 [ 38.000000] md: raid0 personality registered for level 0 [ 38.010000] md: raid1 personality registered for level 1 [ 38.010000] md: raid10 personality registered for level 10 [ 38.020000] md: raid6 personality registered for level 6 [ 38.020000] md: raid5 personality registered for level 5 [ 38.030000] md: raid4 personality registered for level 4 [ 38.030000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-d evel@redhat.com [ 38.040000] cpuidle: using governor ladder [ 38.050000] TCP cubic registered [ 38.050000] NET: Registered protocol family 17 [ 38.050000] NET: Registered protocol family 15 [ 38.060000] registered taskstats version 1 [ 38.060000] md: Waiting for all devices to be available before autodetect [ 38.070000] md: If you don't use raid, use raid=noautodetect [ 38.080000] md: Autodetecting RAID arrays. [ 38.080000] md: Scanned 0 and added 0 devices. [ 38.080000] md: autorun ... [ 38.090000] md: ... autorun DONE. [ 38.090000] EXT3-fs: unable to read superblock [ 38.090000] EXT2-fs: unable to read superblock [ 38.100000] EXT4-fs (md0): unable to read superblock [ 38.100000] List of all partitions: [ 38.110000] 0800 244198584 sda driver: sd [ 38.110000] 0801 510976 sda1 [ 38.120000] 0802 102400 sda2 [ 38.120000] 0803 16384 sda3 [ 38.120000] 0804 243566592 sda4 [ 38.130000] 0810 244198584 sdb driver: sd [ 38.130000] 0811 244093952 sdb1 [ 38.140000] 1f00 512 mtdblock0 (driver?) [ 38.140000] 1f01 2048 mtdblock1 (driver?) [ 38.150000] 1f02 1280 mtdblock2 (driver?) [ 38.150000] 1f03 64 mtdblock3 (driver?) [ 38.160000] 1f04 128 mtdblock4 (driver?) [ 38.160000] 1f05 64 mtdblock5 (driver?) [ 38.170000] 1f06 4096 mtdblock6 (driver?) [ 38.170000] No filesystem could mount root, tried: ext3 ext2 ext4 [ 38.180000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(9,0)

Bonsoir, Grand passionné d'informatique depuis les années 1990 ( seulement en utilisation car malheureusement je n'ai jamais appris à coder ), j'ai essayer tous les systèmes d'exploitations possible en commençant par le système CMP, qui ressemblait au DOS, en passant par toutes les versions de windows jusqu'à la dernière, tater un peu le terrain avec linux bien entendu (redhat, debian, et j'en passe) pour enfin arriver sur mac depuis peu. C'est pas le tout mais avec autant de systèmes différents et autant de logiciels qui les accompagnent, mon système de sauvegarde sur deux disque dur devenait obsolete. N'ayant pas un grand budget mais trouvant le système plutot interessant, j'ai achaté un NAS synology ds411 pour commencer il y a une semaine. Mais pour le mettre en route, c'est une autre histoire .....