Aller au contenu

[R

chouffe

Par chouffe
dans Installation, Démarrage et Configuration

 Partager

Messages recommandés

PatrickH Newbie

PatrickH

Posté(e)
Posté(e)

Pour la commande voir le lien que j'ai mis... faut quand même lire un peu ... hein dry.png

Ensuite activer TELNET dans DSM, installer PuTTY sur ton PC se connecter en "root" (même mot de passe que admin)

Ceci dit si tu débute en Linux à ta place je ne commencerais pas par jouer avec les paramètres avancés des disques dur ... à toi de voir !

Patrick

Lien vers le commentaire
Partager sur d’autres sites
PatrickH Newbie

PatrickH

Posté(e)
Posté(e)

Pour lister les disques

fdisk -l
Pour savoir si ton disque supporte l'AAM 
hdparm -I /dev/sda[/code]




Sur mon disque Samsung l'AAM n'est pas supporté !
[code]DS111> hdparm -I /dev/sda /dev/sda: ATA device, with non-removable media Model Number: SAMSUNG HD204UI Serial Number: S2H7J9KB619043 Firmware Revision: 1AQ10001 Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6 Standards: Used: unknown (minor revision code 0x0028) Supported: 8 7 6 5 Likely used: 8 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 3907029168 Logical Sector size: 512 bytes Physical Sector size: 512 bytes device size with M = 1024*1024: 1907729 MBytes device size with M = 1000*1000: 2000398 MBytes (2000 GB) cache/buffer size = unknown Form Factor: 3.5 inch Nominal Media Rotation Rate: 5400 Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = ? Advanced power management level: disabled Recommended acoustic management value: 254, current value: 0 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * DOWNLOAD_MICROCODE Advanced Power Management feature set Power-Up In Standby feature set * SET_FEATURES required to spinup after power up SET_MAX security extension [color=#ff0000]Automatic Acoustic Management feature set[/color] * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test * General Purpose Logging feature set * 64-bit World wide name * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Native Command Queueing (NCQ) * Host-initiated interface power management * Phy event counters * NCQ priority information DMA Setup Auto-Activate optimization Device-initiated interface power management * Software settings preservation * SMART Command Transport (SCT) feature set * SCT Long Sector Access (AC1) * SCT LBA Segment Access (AC2) * SCT Error Recovery Control (AC3) * SCT Features Control (AC4) * SCT Data Tables (AC5) Security: Master password revision code = 65534 supported not enabled not locked not frozen not expired: security count supported: enhanced erase 322min for SECURITY ERASE UNIT. 322min for ENHANCED SECURITY ERASE UNIT. Logical Unit WWN Device Identifier: 50024e920588b17c NAA : 5 IEEE OUI : 0024e9 Unique ID : 20588b17c Checksum: correct[/code]

Patrick

Lien vers le commentaire
Partager sur d’autres sites
chouffe Newbie

chouffe

Posté(e)
  • Auteur
Posté(e)

Si si ça marche et j'ai le même modèle de disque que toi ! :

NAS_Synology> hdparm -I /dev/sda

/dev/sda:

ATA device, with non-removable media

Model Number: SAMSUNG HD204UI

Serial Number: S2H7J90B926977

Firmware Revision: 1AQ10001

Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6

Standards:

Used: unknown (minor revision code 0x0028)

Supported: 8 7 6 5

Likely used: 8

Configuration:

Logical max current

cylinders 16383 16383

heads 16 16

sectors/track 63 63

--

CHS current addressable sectors: 16514064

LBA user addressable sectors: 268435455

LBA48 user addressable sectors: 3907029168

Logical Sector size: 512 bytes

Physical Sector size: 512 bytes

device size with M = 1024*1024: 1907729 MBytes

device size with M = 1000*1000: 2000398 MBytes (2000 GB)

cache/buffer size = unknown

Form Factor: 3.5 inch

Nominal Media Rotation Rate: 5400

Capabilities:

LBA, IORDY(can be disabled)

Queue depth: 32

Standby timer values: spec'd by Standard, no device specific minimum

R/W multiple sector transfer: Max = 16 Current = ?

Advanced power management level: disabled

Recommended acoustic management value: 254, current value: 0

DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6

Cycle time: min=120ns recommended=120ns

PIO: pio0 pio1 pio2 pio3 pio4

Cycle time: no flow control=120ns IORDY flow control=120ns

Commands/features:

Enabled Supported:

* SMART feature set

Security Mode feature set

* Power Management feature set

* Write cache

* Look-ahead

* Host Protected Area feature set

* WRITE_BUFFER command

* READ_BUFFER command

* NOP cmd

* DOWNLOAD_MICROCODE

Advanced Power Management feature set

Power-Up In Standby feature set

* SET_FEATURES required to spinup after power up

SET_MAX security extension

Automatic Acoustic Management feature set

* 48-bit Address feature set

* Device Configuration Overlay feature set

* Mandatory FLUSH_CACHE

* FLUSH_CACHE_EXT

* SMART error logging

* SMART self-test

* General Purpose Logging feature set

* 64-bit World wide name

* WRITE_UNCORRECTABLE_EXT command

* {READ,WRITE}_DMA_EXT_GPL commands

* Segmented DOWNLOAD_MICROCODE

* Gen1 signaling speed (1.5Gb/s)

* Gen2 signaling speed (3.0Gb/s)

* Native Command Queueing (NCQ)

* Host-initiated interface power management

* Phy event counters

* NCQ priority information

DMA Setup Auto-Activate optimization

Device-initiated interface power management

* Software settings preservation

* SMART Command Transport (SCT) feature set

* SCT Long Sector Access (AC1)

* SCT LBA Segment Access (AC2)

* SCT Error Recovery Control (AC3)

* SCT Features Control (AC4)

* SCT Data Tables (AC5)

Security:

Master password revision code = 65534

supported

not enabled

not locked

not frozen

not expired: security count

supported: enhanced erase

318min for SECURITY ERASE UNIT. 318min for ENHANCED SECURITY ERASE UNIT.

Logical Unit WWN Device Identifier: 50024e920630f423

NAA : 5

IEEE OUI : 0024e9

Unique ID : 20630f423

Checksum: correct

NAS_Synology> hdparm -M128 /dev/sda

/dev/sda:

setting acoustic management to 128

acoustic = 128 (128=quiet ... 254=fast)

NAS_Synology> hdparm -I /dev/sda

/dev/sda:

ATA device, with non-removable media

Model Number: SAMSUNG HD204UI

Serial Number: S2H7J90B926977

Firmware Revision: 1AQ10001

Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6

Standards:

Used: unknown (minor revision code 0x0028)

Supported: 8 7 6 5

Likely used: 8

Configuration:

Logical max current

cylinders 16383 16383

heads 16 16

sectors/track 63 63

--

CHS current addressable sectors: 16514064

LBA user addressable sectors: 268435455

LBA48 user addressable sectors: 3907029168

Logical Sector size: 512 bytes

Physical Sector size: 512 bytes

device size with M = 1024*1024: 1907729 MBytes

device size with M = 1000*1000: 2000398 MBytes (2000 GB)

cache/buffer size = unknown

Form Factor: 3.5 inch

Nominal Media Rotation Rate: 5400

Capabilities:

LBA, IORDY(can be disabled)

Queue depth: 32

Standby timer values: spec'd by Standard, no device specific minimum

R/W multiple sector transfer: Max = 16 Current = ?

Advanced power management level: disabled

Recommended acoustic management value: 254, current value: 128

DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6

Cycle time: min=120ns recommended=120ns

PIO: pio0 pio1 pio2 pio3 pio4

Cycle time: no flow control=120ns IORDY flow control=120ns

Commands/features:

Enabled Supported:

* SMART feature set

Security Mode feature set

* Power Management feature set

* Write cache

* Look-ahead

* Host Protected Area feature set

* WRITE_BUFFER command

* READ_BUFFER command

* NOP cmd

* DOWNLOAD_MICROCODE

Advanced Power Management feature set

Power-Up In Standby feature set

* SET_FEATURES required to spinup after power up

SET_MAX security extension

* Automatic Acoustic Management feature set

* 48-bit Address feature set

* Device Configuration Overlay feature set

* Mandatory FLUSH_CACHE

* FLUSH_CACHE_EXT

* SMART error logging

* SMART self-test

* General Purpose Logging feature set

* 64-bit World wide name

* WRITE_UNCORRECTABLE_EXT command

* {READ,WRITE}_DMA_EXT_GPL commands

* Segmented DOWNLOAD_MICROCODE

* Gen1 signaling speed (1.5Gb/s)

* Gen2 signaling speed (3.0Gb/s)

* Native Command Queueing (NCQ)

* Host-initiated interface power management

* Phy event counters

* NCQ priority information

DMA Setup Auto-Activate optimization

Device-initiated interface power management

* Software settings preservation

* SMART Command Transport (SCT) feature set

* SCT Long Sector Access (AC1)

* SCT LBA Segment Access (AC2)

* SCT Error Recovery Control (AC3)

* SCT Features Control (AC4)

* SCT Data Tables (AC5)

Security:

Master password revision code = 65534

supported

not enabled

not locked

not frozen

not expired: security count

supported: enhanced erase

318min for SECURITY ERASE UNIT. 318min for ENHANCED SECURITY ERASE UNIT.

Logical Unit WWN Device Identifier: 50024e920630f423

NAA : 5

IEEE OUI : 0024e9

Unique ID : 20630f423

Checksum: correct

Lien vers le commentaire
Partager sur d’autres sites
Invité
Ce sujet ne peut plus recevoir de nouvelles réponses.
 Partager
Aller sur la liste des sujets
×
×
  • Créer...

Information importante

Nous avons placé des cookies sur votre appareil pour aider à améliorer ce site. Vous pouvez choisir d’ajuster vos paramètres de cookie, sinon nous supposerons que vous êtes d’accord pour continuer.